Sustainable and Eco friendly products - from paints and wood oils to insulation and more...
Osmo Natural Wood Oils for Wooden Floors
Call and Collect Service
Call us now: 01239 623506 to see if what you want is in stock, or order on our webshop.
We will put your order together the same day and have it ready for you to pick up, or send it to you.
Open 8.30am till 5.30pm
Celtic Sustainables
Unit 9
Parc Teifi
Cardigan
SA43 1EW
BUY NOW Wood Wax Finish Transparent
BUY NOW Wood Wax Finish Clear Extra Thin
BUY NOW Wood Wax Finish Creativ Colour
Buy now from our Online Shop
Applying Osmo to a Wooden Floor.
Can I stain my wooden floor a different colour?
Osmo Polyx Oil Tints can be applied easily using a firm brush. The Osmo Wood Wax Finishes should be applied using a firm brush, then allow it to work in for a few minutes and then wipe off the excess with a cloth, following the grain of the wood. Leave the floor to dry overnight, ensuring that there is good ventillation and then apply one thin coat of Polyx Oil to finish.
How should I prepare the surface of my wood floor?
The surface should be sanded following the grain of the wood and finished with 120- 150 grit sandpaper. Care should be taken to remove all scratch marks.
What happens if I damage part of my floor?
Unlike many traditional lacquers, damaged areas on floors treated with our products can be sanded and re-treated with the same products without any visible brushmarks.
Do I need to sand between coats?
You should always assess the surface before applying the second coat, as sanding between coats maybe necessary.
Is there anything special to watch out for when treating hardwood floors?
Some Hardwood floors such as jatoba and merbau are dense and have a high oil content, which reduces their capacity to absorb other finishes. We recommend treating woods such as these with Wood Wax Finish Clear Extra Thin.
What happens if I over apply the product when treating a floor?
If you have applied too much Polyx Oil, the drying time will be extended considerably. If this happens, provide additional ventillation by opening windows and doors so that the product can dry naturally by oxidation. If damage occurs to the surface as a result, repair the surface as described above.
What happens if I under apply the product when treating a floor?
If you have applied too little of the product, the surface may watermark, the wood may dry out or appear dull. In such cases, please apply another thin coat of Osmo Polyx Oil.
Can I mix all the Osmo colour shades among each other?
Yes. The colour shades of the respective product ranges can be mixed in any ratio. The Osmo Wood Wax Finishes are mixable allowing for a larger colour range.
How long does the surface take to dry?
Osmo products dry within 8-10 hours (except Polyx Oil Rapid 4-6h). The surface dries by oxidation and absorption. Please ensure that there is sufficient ventilation for drying purposes.
When can I walk on the floor again?
As a general rule, the floor can be used one day after the final coat is applied. However, you must make sure that the final coat is dry to touch. The surface will take 14 days to cure completly. As a result, we recommend that rugs etc are first placed on the surface after 2-3 weeks.
Does the floor need polishing once the final coat of Osmo Polyx Oil has been applied?
No, at this stage no further floor treatment is necessary. However, the surface may be buffed with a single-disc buffing machine (white pad) once completely dry. If a higher level of sheen is desired, the floor can be treated after one day at the earliest with Osmo Liquid Wax Cleaner and then polished.
How do I maintain my floor?
This all depends on how much is used. For regular, protective cleaning, we recommend adding Osmo Wash and Care to the mop water. If the floor starts to look dull and lifeless, simply refresh it using Osmo Liquid Wax Cleaner. This can be done in small areas, e.g. under doors or where there are rub marks, without needing to refresh the whole floor area as our products leave no visible brush marks. If the signs of wear and tear are more substaintial, the floor should be retreated with Osmo Polyx Oil.
Why does the colour in the tin look different that after it has been applied?
Depending on the wood species they are applied on, finishes can appear differently in colour shade. This shade does not have to match the small sticker on the tin. We recommend to apply a small sample treatment on a similar piece of wood before complete application.
How should the wood surface be prepared before using Osmo colour?
The surface must be clean, dry (moisture content max, 20%) and frost free.
Does Osmo products contain harmful substances?
Osmo products are produced on a base of carefully refined plant oils and waxes. The surface is safe for humans, animals and plants when dry. Also suitable for children's toys.